The default time before the filter pump will switch off is 12 hours. Your spa thermometer is not reading the correct temperature.
Landen 60p 17 Gal Rimless Low Iron Aquarium Tank 23 6 L 11 8 W 14 2 H Ft 6 Landen Fresh Water
Outside temperatures are too low to operate.
Pentair easy touch water temperature error. Improper plumbing valve settings. C is considered safe for a healthy adult. If this error displays multiple times then there may be a problem with the pumps rotating assembly.
See page 14 Pump Disassembly for instructions for disassembling the pump. If Heater is enabled in the Heat menu see page 18 pressing the Filter Pump button will also enable the selected heat source HeaterSolar LED on. For connector locations refer to the EasyTouch System Wiring Diagram on page 64.
May 21 2013 I just got a Pentair Easytouch control system installed. Page 2 EasyTouchIntelliTouch. A temperature of 100.
Low water flow when switched to spa mode or the control is not in spa mode. Relay connectors - FLTR PUMP - AUX 1 - 7 EasyTouch 8 AUX 1 - 3 EasyTouch 4 Temperature sensors connectors - WATER SOLAR AIR. If Heater is enabled in the Heat menu see page 25 pressing the Filter Pump button will also enable the selected heat source HeaterSolar LED on.
Refrigerant systems low-pressure switch is open. Please disassemble the pump and investigate to see if there is a problem with the impeller or mechanical seal. Press the Valves V button to toggle between Pool and Spa mode and rotate valves.
Add an optional ScreenLogic2 interface kit to your EasyTouch system and you can control everything from pool and spa temperatures to jets lighting water features and moreright from your favorite mobile digital device. Page 1 EASYTOUCH INTELLITOUCH. Pentair heat pump error code LOW REFRIG LOW REFRIG.
The default time before the filter pump will switch off is 12 hours. Pool Features Lights 650 Schedule Usage Chemistry Status INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS. Check that the following plugs are seated correctly on the EasyTouch Load Center motherboard.
Suction leak allowing air into the water flow. Then I commanded a higher water temp and heater came on as it should reaching set points and shutting off burner as it should then cycles on as water temp dictates. EasyTouch 8 and 4 Pool and Spa Control System Users Guide PN 520584 EasyTouch 8 and 4 Installation Guide PN 520583 EasyTouch Accessories EasyTouch Indoor Control Panel 4 Circuits PN 520548 EasyTouch Indoor Control Panel 8 Circuits PN 520549 EasyTouch Wireless Control Panel 4 circuits PN 520546.
1A Power Module over current detected. This picks up the water temperature and relays it to the circuit board to tell it when to turn on and off. When I try to check the water temperature the system reports err.
Special caution is suggested for young children. The pool temperature sensor was not registering the correct temperature so I replaced it. The air temperature function seems to work fine.
Seek professional heat pump repair. While the valves are. Drinking of alcoholic beverages before or during spa or hot tub.
Heat exchanger clogged with debris. If the sensor has failed and is reading the wrong temperature it will cause the same issue youre experiencing. The next day I powered pool-on and it registered the correct water temp.
I see one of the temperature sensors is dangling in the air and another is sticking into the pump outflow pipe. Jul 25 2011 Temperature Sensor Replacement for Pentair. It worked well for the last 3 days.
Press the Valves V button to toggle between Pool and Spa mode and rotate valves. Spa or hot tub water temperatures should never exceed 104. Oct 08 2013 I have a Pentair EasyTouch control system for my 30 month old pool.
Oct 01 2008 Press the Valves V button to toggle between Pool and Spa mode and rotate valves. Press the button again to switch the filter pump off. Pentair heat pump error.
That temperature was not correct either this time 10F low previously about 10F high. The default time. Jun 24 2012 The most likely cause of that is going to be your temperature sensor or your thermistor as its called for that model.
The original black water sensor was causing the Easy Touch - IntelliTouch water temp. If Heater is enabled in the Heat menu see page 23 pressing the Filter Pump button will also enable the selected heat source HeaterSolar LED on. CONTROL SYSTEM UPGRADE TO INTELLICENTER CONTROL SYSTEM For Systems 2012 or Newer Air Temp 65.
Press the Pool P button to activate the filter pump rotate the poolspa valve actuators and circulate the pool water and switch on the heater if enabled in the Heat menu. The unit may have a refrigerant leak. Air blower is running.
Internal bypass valve damaged or clogged with debris. Have pool heater tech check if the switch needs to be replaced. Unit is plumbed backwards.
Prolonged immersion in hot water can induce hyperthermia.